The header doesn't make use of any symbols declared in <linux/pwm.h>.
There are tree files that #include <mfd/lp3943.h>. Two of them
(i.e. drivers/gpio/gpio-lp3943.c and drivers/mfd/lp3943.c) also don't
use any and the third (drivers/pwm/pwm-lp3943.c) has an explicit include
of <linux/pwm.h> itself.
So drop the unused include. The intended side effect is that
drivers/gpio/gpio-lp3943.c and drivers/mfd/lp3943.c stop importing the
"PWM" module namespace.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20250212170403.36619-2-u.kleine-koenig@baylibre.com
Signed-off-by: Lee Jones <lee@kernel.org>
Utilise devm_*() managed resource helpers for freeing IRQs instead.
Reported-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Lee Jones <lee@kernel.org>
The chipid macro/variable and regmap_read function call is not needed
because the TPS65219_REG_TI_DEV_ID register value is not a consistent value
across TPS65219 PMIC config versions. Reading from the DEV_ID register
without a consistent value to compare it to isn't useful. There isn't a
way to verify the match data ID is the same ID read from the DEV_ID device
register. 0xF0 isn't a DEV_ID value consistent across TPS65219 NVM
configurations.
For TPS65215, there is a consistent value in bits 5-0 of the DEV_ID
register. However, there are other error checks in place within probe()
that apply to both PMICs rather than keeping this isolated check for one
PMIC.
Signed-off-by: Shree Ramamoorthy <s-ramamoorthy@ti.com>
Link: https://lore.kernel.org/r/20250206173725.386720-4-s-ramamoorthy@ti.com
Signed-off-by: Lee Jones <lee@kernel.org>
- TPS65214 is a Power Management IC with 3 Buck regulators and 2 LDOs.
- TPS65214 has 2 LDOS and 1 GPO, whereas TPS65219 has 4 LDOs and 2 GPOs.
- TPS65214's LDO1 maps to TPS65219's LDO3.
- A key difference between TPS65215 & TPS65214 are the LDO current and
voltage output ranges and the configurable options available.
- The remaining features for both devices are the same.
Signed-off-by: Shree Ramamoorthy <s-ramamoorthy@ti.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250206173725.386720-3-s-ramamoorthy@ti.com
Signed-off-by: Lee Jones <lee@kernel.org>
If offset end up being high enough, right hand expression in functions
like sm501_gpio_set() shifted left for that number of bits, may
not fit in int type.
Just in case, fix that by using BIT() both as an option safe from
overflow issues and to make this step look similar to other gpio
drivers.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: f61be273d3 ("sm501: add gpiolib support")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://lore.kernel.org/r/20250115171206.20308-1-n.zhandarovich@fintech.ru
Signed-off-by: Lee Jones <lee@kernel.org>
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250114192538.911970-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
Add support for STM32MP25 SoC. Use newly introduced compatible, to handle
new features.
Identification and hardware configuration registers allow to read the
timer version and capabilities (counter width, number of channels...).
So, rework the probe to avoid touching ARR register by simply read the
counter width when available. This may avoid messing with a possibly
running timer.
Also add useful bit fields to stm32-timers header file.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20250110091922.980627-3-fabrice.gasnier@foss.st.com
Signed-off-by: Lee Jones <lee@kernel.org>
Add a new stm32mp25 compatible to stm32-timer dt-bindings in order to
support the STM32MP25 SoC. Some features has been added or updated in
the stm32-timer timer such as:
- hardware configuration and identification registers to read the timer
version and capabilities (counter width, number of channels...)
- dithering mode (can be used to extend PWM resolution)
- input triggers list
- new counter modes
- various bit-field updates
- power-domains property
Timer trigger identifier can be up to 19 (from timer 20)
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20250110091922.980627-2-fabrice.gasnier@foss.st.com
Signed-off-by: Lee Jones <lee@kernel.org>
Pull turbostat updates from Len Brown:
- Fix regression that affinitized forked child in one-shot mode.
- Harden one-shot mode against hotplug online/offline
- Enable RAPL SysWatt column by default
- Add initial PTL, CWF platform support
- Harden initial PMT code in response to early use
- Enable first built-in PMT counter: CWF c1e residency
- Refuse to run on unsupported platforms without --force, to encourage
updating to a version that supports the system, and to avoid
no-so-useful measurement results
* tag 'turbostat-2025.02.02' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (25 commits)
tools/power turbostat: version 2025.02.02
tools/power turbostat: Add CPU%c1e BIC for CWF
tools/power turbostat: Harden one-shot mode against cpu offline
tools/power turbostat: Fix forked child affinity regression
tools/power turbostat: Add tcore clock PMT type
tools/power turbostat: version 2025.01.14
tools/power turbostat: Allow adding PMT counters directly by sysfs path
tools/power turbostat: Allow mapping multiple PMT files with the same GUID
tools/power turbostat: Add PMT directory iterator helper
tools/power turbostat: Extend PMT identification with a sequence number
tools/power turbostat: Return default value for unmapped PMT domains
tools/power turbostat: Check for non-zero value when MSR probing
tools/power turbostat: Enhance turbostat self-performance visibility
tools/power turbostat: Add fixed RAPL PSYS divisor for SPR
tools/power turbostat: Fix PMT mmaped file size rounding
tools/power turbostat: Remove SysWatt from DISABLED_BY_DEFAULT
tools/power turbostat: Add an NMI column
tools/power turbostat: add Busy% to "show idle"
tools/power turbostat: Introduce --force parameter
tools/power turbostat: Improve --help output
...
Pull sh updates from John Paul Adrian Glaubitz:
"Fixes and improvements for sh:
- replace seq_printf() with the more efficient
seq_put_decimal_ull_width() to increase performance when stress
reading /proc/interrupts (David Wang)
- migrate sh to the generic rule for built-in DTB to help avoid race
conditions during parallel builds which can occur because Kbuild
decends into arch/*/boot/dts twice (Masahiro Yamada)
- replace select with imply in the board Kconfig for enabling
hardware with complex dependencies. This addresses warnings which
were reported by the kernel test robot (Geert Uytterhoeven)"
* tag 'sh-for-v6.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: boards: Use imply to enable hardware with complex dependencies
sh: Migrate to the generic rule for built-in DTB
sh: irq: Use seq_put_decimal_ull_width() for decimal values
Summary of Changes since 2024.11.30:
Fix regression in 2023.11.07 that affinitized forked child
in one-shot mode.
Harden one-shot mode against hotplug online/offline
Enable RAPL SysWatt column by default.
Add initial PTL, CWF platform support.
Harden initial PMT code in response to early use.
Enable first built-in PMT counter: CWF c1e residency
Refuse to run on unsupported platforms without --force,
to encourage updating to a version that supports the system,
and to avoid no-so-useful measurement results.
Signed-off-by: Len Brown <len.brown@intel.com>
Pull misc vfs cleanups from Al Viro:
"Two unrelated patches - one is a removal of long-obsolete include in
overlayfs (it used to need fs/internal.h, but the extern it wanted has
been moved back to include/linux/namei.h) and another introduces
convenience helper constructing struct qstr by a NUL-terminated
string"
* tag 'pull-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
add a string-to-qstr constructor
fs/overlayfs/namei.c: get rid of include ../internal.h
Pull MIPS fix from Thomas Bogendoerfer:
"Revert commit breaking sysv ipc for o32 ABI"
* tag 'mips_6.14_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
Revert "mips: fix shmctl/semctl/msgctl syscall for o32"
Pull more smb client updates from Steve French:
- various updates for special file handling: symlink handling,
support for creating sockets, cleanups, new mount options (e.g. to
allow disabling using reparse points for them, and to allow
overriding the way symlinks are saved), and fixes to error paths
- fix for kerberos mounts (allow IAKerb)
- SMB1 fix for stat and for setting SACL (auditing)
- fix an incorrect error code mapping
- cleanups"
* tag 'v6.14-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6: (21 commits)
cifs: Fix parsing native symlinks directory/file type
cifs: update internal version number
cifs: Add support for creating WSL-style symlinks
smb3: add support for IAKerb
cifs: Fix struct FILE_ALL_INFO
cifs: Add support for creating NFS-style symlinks
cifs: Add support for creating native Windows sockets
cifs: Add mount option -o reparse=none
cifs: Add mount option -o symlink= for choosing symlink create type
cifs: Fix creating and resolving absolute NT-style symlinks
cifs: Simplify reparse point check in cifs_query_path_info() function
cifs: Remove symlink member from cifs_open_info_data union
cifs: Update description about ACL permissions
cifs: Rename struct reparse_posix_data to reparse_nfs_data_buffer and move to common/smb2pdu.h
cifs: Remove struct reparse_posix_data from struct cifs_open_info_data
cifs: Remove unicode parameter from parse_reparse_point() function
cifs: Fix getting and setting SACLs over SMB1
cifs: Remove intermediate object of failed create SFU call
cifs: Validate EAs for WSL reparse points
cifs: Change translation of STATUS_PRIVILEGE_NOT_HELD to -EPERM
...
Pull debugfs fix from Greg KH:
"Here is a single debugfs fix from Al to resolve a reported regression
in the driver-core tree. It has been reported to fix the issue"
* tag 'driver-core-6.14-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
debugfs: Fix the missing initializations in __debugfs_file_get()
Pull misc fixes from Andrew Morton:
"21 hotfixes. 8 are cc:stable and the remainder address post-6.13
issues. 13 are for MM and 8 are for non-MM.
All are singletons, please see the changelogs for details"
* tag 'mm-hotfixes-stable-2025-02-01-03-56' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (21 commits)
MAINTAINERS: include linux-mm for xarray maintenance
revert "xarray: port tests to kunit"
MAINTAINERS: add lib/test_xarray.c
mailmap, MAINTAINERS, docs: update Carlos's email address
mm/hugetlb: fix hugepage allocation for interleaved memory nodes
mm: gup: fix infinite loop within __get_longterm_locked
mm, swap: fix reclaim offset calculation error during allocation
.mailmap: update email address for Christopher Obbard
kfence: skip __GFP_THISNODE allocations on NUMA systems
nilfs2: fix possible int overflows in nilfs_fiemap()
mm: compaction: use the proper flag to determine watermarks
kernel: be more careful about dup_mmap() failures and uprobe registering
mm/fake-numa: handle cases with no SRAT info
mm: kmemleak: fix upper boundary check for physical address objects
mailmap: add an entry for Hamza Mahfooz
MAINTAINERS: mailmap: update Yosry Ahmed's email address
scripts/gdb: fix aarch64 userspace detection in get_current_task
mm/vmscan: accumulate nr_demoted for accurate demotion statistics
ocfs2: fix incorrect CPU endianness conversion causing mount failure
mm/zsmalloc: add __maybe_unused attribute for is_first_zpdesc()
...
Pull media fix from Mauro Carvalho Chehab:
"A revert for a regression in the uvcvideo driver"
* tag 'media/v6.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
Revert "media: uvcvideo: Require entities to have a non-zero unique ID"
