This patch enhances vmxnet3 to support latency measurement.
This support will help to track the latency in packet processing
between guest virtual nic driver and host. For this purpose, we
introduce a new timestamp ring in vmxnet3 which will be per Tx/Rx
queue. This ring will be used to carry timestamp of the packets
which will be used to calculate the latency.
User can enable latency measurement using realtime knob in vnic
setting in VCenter.
Signed-off-by: Ronak Doshi <ronak.doshi@broadcom.com>
Acked-by: Guolin Yang <guolin.yang@broadcom.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240531193050.4132-3-ronak.doshi@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current ionic devices only support 52 internal physical address
lines. This is sufficient for x86_64 systems which have similar
limitations but does not apply to all other architectures,
notably IBM POWER (ppc64). To ensure that MSI/MSI-X vectors are
not set outside the physical address limits of the NIC, set the
no_64bit_msi value of the pci_dev structure during device probe.
Signed-off-by: David Christensen <drc@linux.ibm.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20240603212747.1079134-1-drc@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kevin Yang says:
====================
tcp: add sysctl_tcp_rto_min_us
Adding a sysctl knob to allow user to specify a default
rto_min at socket init time.
After this patch series, the rto_min will has multiple sources:
route option has the highest precedence, followed by the
TCP_BPF_RTO_MIN socket option, followed by this new
tcp_rto_min_us sysctl.
v3:
fix typo, simplify min/max_t to min/max
v2:
fit line width to 80 column.
v2: https://lore.kernel.org/netdev/20240530153436.2202800-1-yyd@google.com/
v1: https://lore.kernel.org/netdev/20240528171320.1332292-1-yyd@google.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a sysctl knob to allow user to specify a default
rto_min at socket init time, other than using the hard
coded 200ms default rto_min.
Note that the rto_min route option has the highest precedence
for configuring this setting, followed by the TCP_BPF_RTO_MIN
socket option, followed by the tcp_rto_min_us sysctl.
Signed-off-by: Kevin Yang <yyd@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rto_min now has multiple sources, ordered by preprecedence high to
low: ip route option rto_min, icsk->icsk_rto_min.
When derive delack_max from rto_min, we should not only use ip
route option, but should use tcp_rto_min helper to get the correct
rto_min.
Signed-off-by: Kevin Yang <yyd@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
These fields can be read and written locklessly, add annotations
around these minor races.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to dump NIX transmit queue topology.
There are multiple levels of scheduling/shaping supported by
NIX and a packet traverses through multiple levels before sending
the packet out. At each level, there are set of scheduling/shaping
rules applied to a packet flow.
Each packet traverses through multiple levels
SQ->SMQ->TL4->TL3->TL2->TL1 and these levels are mapped in a parent-child
relationship.
This patch dumps the debug information related to all TM Levels in
the following way.
Example:
$ echo <nixlf> > /sys/kernel/debug/octeontx2/nix/tm_tree
$ cat /sys/kernel/debug/octeontx2/nix/tm_tree
A more desriptive set of registers at each level can be dumped
in the following way.
Example:
$ echo <nixlf> > /sys/kernel/debug/octeontx2/nix/tm_topo
$ cat /sys/kernel/debug/octeontx2/nix/tm_topo
Signed-off-by: Anshumali Gaur <agaur@marvell.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET says:
====================
devlink: Constify struct devlink_dpipe_table_ops
Patch 1 updates devl_dpipe_table_register() and struct
devlink_dpipe_table to accept "const struct devlink_dpipe_table_ops".
Then patch 2 updates the only user of this function.
This is compile tested only.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
'struct devlink_dpipe_table_ops' are not modified in this driver.
Constifying these structures moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
15557 712 0 16269 3f8d drivers/net/ethernet/mellanox/mlxsw/spectrum_dpipe.o
After:
=====
text data bss dec hex filename
15789 488 0 16277 3f95 drivers/net/ethernet/mellanox/mlxsw/spectrum_dpipe.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"struct devlink_dpipe_table_ops" only contains some function pointers.
Update "struct devlink_dpipe_table" and the 'table_ops' parameter of
devl_dpipe_table_register() so that structures in drivers can be
constified.
Constifying these structures will move some data to a read-only section, so
increase overall security.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aquantia Ethernet PHYs got 3 LED output pins which are typically used
to indicate link status and activity.
Add a minimal LED controller driver supporting the most common uses
with the 'netdev' trigger as well as software-driven forced control of
the LEDs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[ rework indentation, fix checkpatch error and improve some functions ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for LEDs support, move priv and hw stat to header to
reference priv struct also in other .c outside aquantia.main
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
'cable_test_tdr_req_info' is unused since the original
commit f2bc8ad31a ("net: ethtool: Allow PHY cable test TDR data to
configured").
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
'cfpktq' has been unused since
commit 73d6ac633c ("caif: code cleanup").
'caif_packet_funcs' is declared but never defined.
Remove both of them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I was doing some experiments, I found that when using the first
parameter, namely, struct net, in ip_metrics_convert() always triggers NULL
pointer crash. Then I digged into this part, realizing that we can remove
this one due to its uselessness.
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Smatch complains:
net/bridge/br_netlink_tunnel.c:
318 br_process_vlan_tunnel_info() warn: inconsistent indenting
Fix it with a proper indenting
Signed-off-by: Chen Hanxiao <chenhx.fnst@fujitsu.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This rewrites the Vitesse VSC73xx DSA switches DT binding in
schema.
It was a bit tricky since I needed to come up with some way
of applying the SPI properties only on SPI devices and not
platform devices, but I figured something out that works.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3e2f544dd8 ("net: get stats64 if device if driver is
configured") moved the callback to dev_get_tstats64() to net core, so,
unless the driver is doing some custom stats collection, it does not
need to set .ndo_get_stats64.
Since this driver is now relying in NETDEV_PCPU_STAT_TSTATS, then, it
doesn't need to set the dev_get_tstats64() generic .ndo_get_stats64
function pointer.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://lore.kernel.org/r/20240531111552.3209198-2-leitao@debian.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
With commit 34d21de99c ("net: Move {l,t,d}stats allocation to core and
convert veth & vrf"), stats allocation could be done on net core instead
of this driver.
With this new approach, the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc). This is core responsibility now.
Move openvswitch driver to leverage the core allocation.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240531111552.3209198-1-leitao@debian.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski says:
====================
tcp: refactor skb_cmp_decrypted() checks
Refactor the input patch coalescing checks and wrap "EOR forcing"
logic into a helper. This will hopefully make the code easier to
follow. While at it throw some DEBUG_NET checks into skb_shift().
====================
Link: https://lore.kernel.org/r/20240530233616.85897-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
According to current semantics we should never try to shift data
between skbs which differ on decrypted or pp_recycle status.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
TLS (and hopefully soon PSP will) use EOR to prevent skbs
with different decrypted state from getting merged, without
adding new tests to the skb handling. In both cases once
the connection switches to an "encrypted" state, all subsequent
skbs will be encrypted, so a single "EOR fence" is sufficient
to prevent mixing.
Add a helper for setting the EOR bit, to make this arrangement
more explicit.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
tcp_skb_can_collapse() checks for conditions which don't make
sense on input. Because of this we ended up sprinkling a few
pairs of mptcp_skb_can_collapse() and skb_cmp_decrypted() calls
on the input path. Group them in a new helper. This should make
it less likely that someone will check mptcp and not decrypted
or vice versa when adding new code.
This implicitly adds a decrypted check early in tcp_collapse().
AFAIU this will very slightly increase our ability to collapse
packets under memory pressure, not a real bug.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Davide Caratti says:
====================
net: allow dissecting/matching tunnel control flags
Ilya says: "for correct matching on decapsulated packets, we should match
on not only tunnel id and headers, but also on tunnel configuration flags
like TUNNEL_NO_CSUM and TUNNEL_DONT_FRAGMENT. This is done to distinguish
similar tunnels with slightly different configs. And it is important since
tunnel configuration is flow based, i.e. can be different for every packet,
even though the main tunnel port is the same."
- patch 1 extends the kernel's flow dissector to extract these flags
from the packet's tunnel metadata.
- patch 2 extends TC flower to match on any combination of TUNNEL_NO_CSUM,
TUNNEL_DONT_FRAGMENT, TUNNEL_OAM, TUNNEL_CRIT_OPT
v4:
- fix kernel-doc warning in flow_dissector.h (thanks Jakub)
v3:
- rebase on top of new uAPI bits and internals after commit 5832c4a77d
("ip_tunnel: convert __be16 tunnel flags to bitmaps"). Use of network
byte order is no more needed, since these bits match on metadata: convert
netlink attributes to be u32.
- also include TUNNEL_CRIT_OPT
v2:
- use NL_REQ_ATTR_CHECK() where possible (thanks Jamal)
- don't overwrite 'ret' in the error path of fl_set_key_flags()
====================
Link: https://lore.kernel.org/r/cover.1717088241.git.dcaratti@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Dissect [no]csum, [no]dontfrag, [no]oam, [no]crit flags from skb metadata.
This is a prerequisite for matching these control flags using TC flower.
Suggested-by: Ilya Maximets <i.maximets@ovn.org>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Catching and debugging missing qdiscs is pretty tricky. When qdisc
is deleted we replace it with a noop qdisc, which silently drops
all the packets. Since the noop qdisc has a single static instance
we can't count drops at the qdisc level. Count them as dev->tx_drops.
ip netns add red
ip link add type veth peer netns red
ip link set dev veth0 up
ip -netns red link set dev veth0 up
ip a a dev veth0 10.0.0.1/24
ip -netns red a a dev veth0 10.0.0.2/24
ping -c 2 10.0.0.2
# 2 packets transmitted, 2 received, 0% packet loss, time 1031ms
ip -s link show dev veth0
# TX: bytes packets errors dropped carrier collsns
# 1314 17 0 0 0 0
tc qdisc replace dev veth0 root handle 1234: mq
tc qdisc replace dev veth0 parent 1234:1 pfifo
tc qdisc del dev veth0 parent 1234:1
ping -c 2 10.0.0.2
# 2 packets transmitted, 0 received, 100% packet loss, time 1034ms
ip -s link show dev veth0
# TX: bytes packets errors dropped carrier collsns
# 1314 17 0 3 0 0
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20240529162527.3688979-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If we get to the end of the r8152's suspend() routine and we find that
the USB device is INACCESSIBLE then it means that some of our
preparation for suspend didn't take place. We need a USB reset to get
ourselves back in a consistent state so we can try again and that
can't happen during system suspend. Call pm_wakeup_event() to wake the
system up in this case.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/66590f25.170a0220.8b5ad.1752@mx.google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If we happened to get a USB transfer error during the transition to
suspend then the usb_queue_reset_device() that r8152_control_msg()
calls will get dropped on the floor. This is because
usb_lock_device_for_reset() (which usb_queue_reset_device() uses)
silently fails if it's called when a device is suspended or if too
much time passes.
Let's resolve this by resetting the device ourselves in r8152's
resume() function.
NOTE: due to timing, it's _possible_ that we could end up with two USB
resets: the one queued previously and the one called from the resume()
patch. This didn't happen in test cases I ran, though it's conceivably
possible. We can't easily know if this happened since
usb_queue_reset_device() can just silently drop the reset request. In
any case, it's not expected that this is a problem since the two
resets can't run at the same time (because of the device lock) and it
should be OK to reset the device twice. If somehow the double-reset
causes problems we could prevent resets from being queued up while
suspend is running.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/66590f22.170a0220.8b5ad.1750@mx.google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean says:
====================
Probing cleanup for the Felix DSA driver
This is a follow-up to Russell King's request for code consolidation
among felix_vsc9959, seville_vsc9953 and ocelot_ext, stated here:
https://lore.kernel.org/all/Zh1GvcOTXqb7CpQt@shell.armlinux.org.uk/
Details are in individual patches. Testing was done on NXP LS1028A
(felix_vsc9959).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the common felix_register_switch() from the umbrella driver
is the only entity that accesses these data structures, we can remove
them from the list of the exported symbols.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Sai Krishna <saikrishnag@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King suggested that felix_vsc9959, seville_vsc9953 and
ocelot_ext have a large portion of duplicated init code, which could be
made common [1].
[1]: https://lore.kernel.org/all/Zh1GvcOTXqb7CpQt@shell.armlinux.org.uk/
Here, we take the following common steps:
- "felix" and "ds" structure allocation
- "felix", "ocelot" and "ds" basic structure initialization
- dsa_register_switch() call
and we make a common function out of them.
For every driver except felix_vsc9959, this is also the entire probing
procedure. For felix_vsc9959, we also need to do some PCI-specific
stuff, which can easily be reordered to be done before, and unwound on
failure.
We also have to convert the bus-specific platform_set_drvdata() and
pci_set_drvdata() calls into dev_set_drvdata(). But this should have no
impact on the behavior.
Suggested-by: "Russell King (Oracle)" <linux@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King points out that seville_vsc9953 populates
felix->info->num_tx_queues = 8, but this doesn't make it all the way
into ds->num_tx_queues (which is how the user interface netdev queues
get allocated) [1].
[1]: https://lore.kernel.org/all/20240415160150.yejcazpjqvn7vhxu@skbuf/
When num_tx_queues=0 for seville, this is implicitly converted to 1 by
dsa_user_create(), and this is good enough for basic operation for a
switch port. The tc qdisc offload layer works with netdev TX queues,
so for QoS offload we need to pretend we have multiple TX queues. The
VSC9953, like ocelot_ext, doesn't export QoS offload, so it doesn't
really matter. But we can definitely set num_tx_queues=8 for all
switches.
The felix->info->num_tx_queues construct itself seems unnecessary.
It was introduced by commit de143c0e27 ("net: dsa: felix: Configure
Time-Aware Scheduler via taprio offload") at a time when vsc9959
(LS1028A) was the only switch supported by the driver.
8 traffic classes, and 1 queue per traffic class, is a common
architectural feature of all switches in the family. So they could
all just set OCELOT_NUM_TC and be fine.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current placement of devm_request_threaded_irq() is inconvenient.
It is between the allocation of the "felix" structure and
dsa_register_switch(), both of which we'd like to refactor into a
function that's common for all switches. But the IRQ is specific to
felix_vsc9959.
A closer inspection of the felix_irq_handler() code suggests that
it does things that depend on the data structures having been fully
initialized. For example, ocelot_get_txtstamp() takes
&port->tx_skbs.lock, which has only been initialized in
ocelot_init_port() which has not run yet.
It is not one of those IRQF_SHARED IRQs, so CONFIG_DEBUG_SHIRQ_FIXME
shouldn't apply here, and thus, it doesn't really matter, because in
practice, the IRQ will not be triggered so early. Nonetheless, it is a
good practice for the driver to be prepared for it to fire as soon as it
is requested.
Create a new felix->info method for running custom code for vsc9959 from
within felix_setup(), and move the request_irq() call there. The
ocelot_ext should have an IRQ as well, so this should be a step in the
right direction for that model (VSC7512) as well.
Some minor changes are made while moving the code. Casts from void *
aren't necessary, so drop them, and rename felix_irq_handler() to the
more specific vsc9959_irq_handler().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King suggested that felix_vsc9959, seville_vsc9953 and
ocelot_ext have a large portion of duplicated init and teardown code,
which could be made common [1]. The teardown code could even be
simplified away if we made use of devres, something which is used here
and there in the felix driver, just not very consistently.
[1] https://lore.kernel.org/all/Zh1GvcOTXqb7CpQt@shell.armlinux.org.uk/
Prepare the ground in the felix_vsc9959 driver, by allocating the data
structures using devres and deleting the kfree() calls. This also
deletes the "Failed to allocate ..." message, since memory allocation
errors are extremely loud anyway, and it's hard to miss them.
Suggested-by: "Russell King (Oracle)" <linux@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 6fffbc7ae1 ("PCI: Honor firmware's device disabled
status"), PCI device drivers with OF bindings no longer need this check.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King suggested that felix_vsc9959, seville_vsc9953 and
ocelot_ext have a large portion of duplicated init and teardown code,
which could be made common [1]. The teardown code could even be
simplified away if we made use of devres, something which is used here
and there in the felix driver, just not very consistently.
[1] https://lore.kernel.org/all/Zh1GvcOTXqb7CpQt@shell.armlinux.org.uk/
Prepare the ground in the seville_vsc9953 driver, by allocating the data
structures using devres and deleting the kfree() calls. This also
deletes the "Failed to allocate ..." message, since memory allocation
errors are extremely loud anyway, and it's hard to miss them.
Suggested-by: "Russell King (Oracle)" <linux@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King suggested that felix_vsc9959, seville_vsc9953 and
ocelot_ext have a large portion of duplicated init and teardown code,
which could be made common [1]. The teardown code could even be
simplified away if we made use of devres, something which is used here
and there in the felix driver, just not very consistently.
[1] https://lore.kernel.org/all/Zh1GvcOTXqb7CpQt@shell.armlinux.org.uk/
Prepare the ground in the ocelot_ext driver, by allocating the data
structures using devres and deleting the kfree() calls. This also
deletes the "Failed to allocate ..." message, since memory allocation
errors are extremely loud anyway, and it's hard to miss them.
Suggested-by: "Russell King (Oracle)" <linux@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Colin Foster <colin.foster@in-advantage.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guangguan Wang says:
====================
net/smc: Change the upper boundary of SMC-R's snd_buf and rcv_buf to 512MB
SMCR_RMBE_SIZES is the upper boundary of SMC-R's snd_buf and rcv_buf.
The maximum bytes of snd_buf and rcv_buf can be calculated by 2^SMCR_
RMBE_SIZES * 16KB. SMCR_RMBE_SIZES = 5 means the upper boundary is 512KB.
TCP's snd_buf and rcv_buf max size is configured by net.ipv4.tcp_w/rmem[2]
whose default value is 4MB or 6MB, is much larger than SMC-R's upper
boundary.
In some scenarios, such as Recommendation System, the communication
pattern is mainly large size send/recv, where the size of snd_buf and
rcv_buf greatly affects performance. Due to the upper boundary
disadvantage, SMC-R performs poor than TCP in those scenarios. So it
is time to enlarge the upper boundary size of SMC-R's snd_buf and rcv_buf,
so that the SMC-R's snd_buf and rcv_buf can be configured to larger size
for performance gain in such scenarios.
The SMC-R rcv_buf's size will be transferred to peer by the field
rmbe_size in clc accept and confirm message. The length of the field
rmbe_size is four bits, which means the maximum value of SMCR_RMBE_SIZES
is 15. In case of frequently adjusting the value of SMCR_RMBE_SIZES
in different scenarios, set the value of SMCR_RMBE_SIZES to the maximum
value 15, which means the upper boundary of SMC-R's snd_buf and rcv_buf
is 512MB. As the real memory usage is determined by the value of
net.smc.w/rmem, not by the upper boundary, set the value of SMCR_RMBE_SIZES
to the maximum value has no side affects.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
SMCR_RMBE_SIZES is the upper boundary of SMC-R's snd_buf and rcv_buf.
The maximum bytes of snd_buf and rcv_buf can be calculated by 2^SMCR_
RMBE_SIZES * 16KB. SMCR_RMBE_SIZES = 5 means the upper boundary is 512KB.
TCP's snd_buf and rcv_buf max size is configured by net.ipv4.tcp_w/rmem[2]
whose default value is 4MB or 6MB, is much larger than SMC-R's upper
boundary.
In some scenarios, such as Recommendation System, the communication
pattern is mainly large size send/recv, where the size of snd_buf and
rcv_buf greatly affects performance. Due to the upper boundary
disadvantage, SMC-R performs poor than TCP in those scenarios. So it
is time to enlarge the upper boundary size of SMC-R's snd_buf and rcv_buf,
so that the SMC-R's snd_buf and rcv_buf can be configured to larger size
for performance gain in such scenarios.
The SMC-R rcv_buf's size will be transferred to peer by the field
rmbe_size in clc accept and confirm message. The length of the field
rmbe_size is four bits, which means the maximum value of SMCR_RMBE_SIZES
is 15. In case of frequently adjusting the value of SMCR_RMBE_SIZES
in different scenarios, set the value of SMCR_RMBE_SIZES to the maximum
value 15, which means the upper boundary of SMC-R's snd_buf and rcv_buf
is 512MB. As the real memory usage is determined by the value of
net.smc.w/rmem, not by the upper boundary, set the value of SMCR_RMBE_SIZES
to the maximum value has no side affects.
Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com>
Co-developed-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SG_MAX_SINGLE_ALLOC is used to limit maximum number of entries that
will be allocated in one piece of scatterlist. When the entries of
scatterlist exceeds SG_MAX_SINGLE_ALLOC, sg chain will be used. From
commit 7c703e54cc ("arch: switch the default on ARCH_HAS_SG_CHAIN"),
we can know that the macro CONFIG_ARCH_NO_SG_CHAIN is used to identify
whether sg chain is supported. So, SMC-R's rmb buffer should be limited
by SG_MAX_SINGLE_ALLOC only when the macro CONFIG_ARCH_NO_SG_CHAIN is
defined.
Fixes: a3fe3d01bd ("net/smc: introduce sg-logic for RMBs")
Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com>
Co-developed-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When splice() support was added in commit 2b514574f7 ("net:
af_unix: implement splice for stream af_unix sockets"), we had
to release unix_sk(sk)->readlock (current iolock) before calling
splice_to_pipe().
Due to the unlock, commit 73ed5d25dc ("af-unix: fix use-after-free
with concurrent readers while splicing") added a safeguard in
unix_stream_read_generic(); we had to bump the skb refcount before
calling ->recv_actor() and then check if the skb was consumed by a
concurrent reader.
However, the pipe side locking was refactored, and since commit
25869262ef ("skb_splice_bits(): get rid of callback"), we can
call splice_to_pipe() without releasing unix_sk(sk)->iolock.
Now, the skb is always alive after the ->recv_actor() callback,
so let's remove the unnecessary drop_skb logic.
This is mostly the revert of commit 73ed5d25dc ("af-unix: fix
use-after-free with concurrent readers while splicing").
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240529144648.68591-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rengarajan says:
====================
lan78xx: Enable 125 MHz CLK and Auto Speed configuration for LAN7801 if NO EEPROM is detected
This patch series adds the support for 125 MHz clock, Auto speed and
auto duplex configuration for LAN7801 in the absence of EEPROM.
====================
Link: https://lore.kernel.org/r/20240529140256.1849764-1-rengarajan.s@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
